|
About the Copter 3.6 category
|
|
0
|
3721
|
March 19, 2018
|
|
Thrust is not aligned with the throttle
|
|
5
|
51
|
May 1, 2025
|
|
Yuneec ST16 Transmitter Support?
|
|
80
|
13527
|
April 24, 2025
|
|
Frustration about mission planer and arducopter
|
|
30
|
1702
|
April 4, 2025
|
|
PosHold without GPS but optical flow sensor
|
|
7
|
723
|
March 27, 2025
|
|
Autonomous take-off using attitude messages for PixHawk-based quadcopter using MAVROS in GUIDED_NOGPS mode
|
|
19
|
4399
|
March 20, 2025
|
|
Unstable drone after takeoff crashes
|
|
13
|
1801
|
January 17, 2025
|
|
FLIR Duo Pro - Camera Trigger via Mavlink?
|
|
48
|
7593
|
November 18, 2024
|
|
How to make new flightmodes visible in Mission Planner?
|
|
6
|
933
|
October 31, 2024
|
|
Unstable flight with Cube Orange using outdated firmware
|
|
3
|
99
|
October 11, 2024
|
|
WSL waf upload hangs
|
|
2
|
1334
|
August 26, 2024
|
|
How to send a string from a PC to RaspberryPI with telemetry over Pixhawk
|
|
3
|
1560
|
July 30, 2024
|
|
Arducopter autotune fails
|
|
3
|
286
|
July 25, 2024
|
|
Merging modes on one channel
|
|
25
|
1766
|
June 18, 2024
|
|
Multiple MaxBotix I2C Pixhawk 2.1 problem
|
|
71
|
8846
|
June 16, 2024
|
|
Motors inclination
|
|
7
|
2369
|
June 13, 2024
|
|
How to tell if/which RC protocol Arducopter recognizes on SPKT/DSM port?
|
|
6
|
738
|
May 30, 2024
|
|
Power module wire of the drone get fired
|
|
3
|
239
|
May 26, 2024
|
|
Beaglebone Blue no GPS passthrough for Mavlink?
|
|
8
|
2039
|
May 21, 2024
|
|
CRITICAL Copter 3.6.10 Throttle Limit Issue
|
|
12
|
1349
|
May 11, 2024
|
|
Issue with precision loiter and landing
|
|
12
|
814
|
April 18, 2024
|
|
Rplidar A1 360 how to configure
|
|
9
|
2801
|
April 17, 2024
|
|
Precision landing using tether
|
|
14
|
1146
|
April 7, 2024
|
|
Calibration of Optical Flow using PX4Flow
|
|
17
|
3898
|
April 4, 2024
|
|
Unable to get response from px4flow
|
|
8
|
1744
|
March 30, 2024
|
|
Simple Compass Calibration
|
|
1
|
279
|
March 26, 2024
|
|
ArduPilot 3.6 ChibiOS how to configure battery monitor for HolyBro Pixhwak 4 (fmu v5)
|
|
16
|
5401
|
March 20, 2024
|
|
2 Axis Gimbal Configuration
|
|
0
|
203
|
March 20, 2024
|
|
Pixhawk 2.4.8 motor can only be powered by servo rail, but not by the Power Port
|
|
3
|
634
|
March 13, 2024
|
|
Can't arm with RC controller but ok with Mission Planner
|
|
2
|
856
|
March 10, 2024
|