|
Is it possible to run both 4G LTE and video streaming at same raspberry pi (3) and camera (V2.1)?
|
|
1
|
1831
|
October 28, 2021
|
|
Raspberry pi is not getting connected to telemetry port 1 telemetry 2 port is getting connected
|
|
6
|
1020
|
October 27, 2021
|
|
Getting 1% signal only on my Mission planner over 4G LTE on diffrent network
|
|
6
|
1776
|
October 21, 2021
|
|
Some time it's not disarming after landing, throttle is again increasing and drone is falling one side
|
|
4
|
533
|
October 21, 2021
|
|
Can I use range finder for vision based precision landing? Due to altitude variance landing is not happening properly
|
|
9
|
1185
|
October 20, 2021
|
|
Not able to run Precision landing and mav proxy at same time
|
|
5
|
714
|
October 19, 2021
|
|
Some time its YAWING to detect the ARUCO while landing in Vision based precision landing
|
|
0
|
629
|
October 18, 2021
|
|
After last waypoint flight mode is not changing into RTL, Keeping remains Auto mode
|
|
2
|
628
|
October 17, 2021
|
|
Mission Planner Failsafe and Unhealthy AHRS
|
|
2
|
2435
|
September 23, 2021
|
|
Is it important to buy Range finder sensor along with IR lock module for precision landing
|
|
2
|
492
|
September 14, 2021
|
|
Precesion landing with IR lock sensor
|
|
3
|
544
|
June 26, 2021
|
|
How to AUTO RESTART the mission in the air only when it is completing the last way point
|
|
6
|
1682
|
September 8, 2021
|
|
Vision based precision landing, codes getting error in Raspberry pi terminal while uploading
|
|
32
|
2017
|
August 29, 2021
|
|
In Mission planner 9 and 10th chennal is not showing, Using 10 channel tx and rx (FSi6x)
|
|
9
|
1547
|
August 25, 2021
|
|
Loiter more aggressiv break then poshold
|
|
12
|
1267
|
August 23, 2021
|
|
Can I use Pi camera (5 MP)V2.1 for precision landing?
|
|
2
|
763
|
August 21, 2021
|
|
How to make Mission resume after changing the battery using raspberry pi and drone kit code?
|
|
4
|
1003
|
August 16, 2021
|
|
Large Vehicle Mag Calibrate Failed to Execute
|
|
6
|
1472
|
August 16, 2021
|
|
Pixhawk 4 - Check BRD_TYPE: Baro: unable to initialise driver
|
|
8
|
6293
|
August 15, 2021
|
|
Loiter mode once stop moving alttitude is reducing and comming up
|
|
4
|
584
|
August 15, 2021
|
|
How to Connect raspberry pi with mission planner on difffrent network
|
|
5
|
1757
|
August 11, 2021
|
|
Need suggestion on my Autotune Result
|
|
4
|
452
|
August 3, 2021
|
|
Set_rc_channel_pwm() not working
|
|
0
|
1086
|
August 2, 2021
|
|
I am not able to find hover_freq value in the mission planner
|
|
29
|
2186
|
August 1, 2021
|
|
INS_HNTCH_MODE Parameter is not showing in the mission planner
|
|
24
|
1739
|
July 31, 2021
|
|
Need some detailed explanation on FS_OPTIONS
|
|
1
|
1078
|
July 28, 2021
|
|
How to calibrate ESC and where is the safety switch?
|
|
3
|
1721
|
July 23, 2021
|
|
Position hold and QGC
|
|
5
|
797
|
July 19, 2021
|
|
Quadcopter using (Pixhawk 4) Motor 1 and 2 are heating up and motor 3 and 4 are fine
|
|
29
|
3347
|
July 14, 2021
|
|
How to connect ESC's signal cable to Pixhawk-4 without soldering them
|
|
4
|
640
|
July 13, 2021
|