About the Rovers and boats category
|
|
0
|
1035
|
February 3, 2014
|
RC boat compatibility with ArduPilot
|
|
7
|
80
|
May 20, 2022
|
Buck Converter Recommendations
|
|
16
|
155
|
May 17, 2022
|
Obstacle Avoidance with OPTICAL FLOW & LIDAR SENSOR 3901-L0X
|
|
0
|
38
|
May 12, 2022
|
help with hardware ( autonomous mowe)
|
|
5
|
54
|
May 9, 2022
|
Brushed esc for tracked tank
|
|
2
|
54
|
May 1, 2022
|
Steering wheel with hydraulic steering - how to interface?
|
|
2
|
83
|
April 25, 2022
|
Winch for Rover?
|
|
4
|
125
|
March 21, 2022
|
Soliciting Boat Hardware Advice/General Questions
|
|
5
|
259
|
March 20, 2022
|
Getting IMU errors on new boat
|
|
12
|
250
|
March 8, 2022
|
NooB Questions Hardware for Rover and Glider
|
|
0
|
94
|
February 21, 2022
|
On/Off switch for cutting off power/current?
|
|
14
|
266
|
February 10, 2022
|
Motor Recommendation for a Low Speed Long Range RC Boat
|
|
0
|
130
|
February 2, 2022
|
Turn on motor reverse with AUX channel
|
|
8
|
196
|
January 23, 2022
|
Adventures with a "mixed mode" motor controller
|
|
2
|
184
|
December 6, 2021
|
VL53L1X Lidar i2c address change
|
|
8
|
669
|
November 30, 2021
|
Durandal issues
|
|
0
|
146
|
November 22, 2021
|
Linking 2 rudders to apm board
|
|
1
|
271
|
November 18, 2021
|
Here3 and CAN support on Matek F405 wing Rover build?
|
|
1
|
138
|
November 5, 2021
|
New/First Build Noob
|
|
7
|
290
|
November 3, 2021
|
Gamepad Buttons for rover
|
|
0
|
129
|
July 17, 2021
|
Manned autonomous boat rudder control
|
|
4
|
604
|
July 17, 2021
|
Troubleshooting Airmar DT800
|
|
0
|
153
|
July 14, 2021
|
Arducopter - Rover with L298 Motor Driver Module
|
|
13
|
3278
|
May 19, 2021
|
Problems connecting ESC to Omnibus F4 v6
|
|
0
|
152
|
April 6, 2021
|
Gyro and ultrasonic sensor with only one servo
|
|
0
|
141
|
April 5, 2021
|
Suggestions for hardware - is this a viable project? Trolling Motor conversion
|
|
3
|
305
|
April 2, 2021
|
Motors for Rover
|
|
14
|
409
|
March 25, 2021
|
Help apm 2.8 trigger a relay
|
|
0
|
146
|
March 24, 2021
|
Omnibus F4 V3 PRO - GPIO pin 56 (PWM 7) not available for assignment.This pin is used for Camera Control
|
|
2
|
355
|
February 21, 2021
|