@SIYI can i get old firmware for zr30 gimble camera because after update the firmware i didn’t get feed in mk15 tx
Please confirm if you successfully flashed all three firmware by following the video below.
If you have changed the IP addresses before flashing, the new firmware will reset the IP addresses to 192.168.144.25
Hey, all the three firmwares have been flashed as shown in the video. The IP address is also 192.168.144.25
The link status in tx is showing connected. Bit i am still not able to receive the feed from the camera
I am attaching the required photos and videos of the same.
Thanks
https://drive.google.com/drive/folders/1OKqZFQO8yTIBhAf_7p6TKuJAyQReKDix?usp=sharing
- Please update the SIYI FPV app
- Please check the IP addresses settings in SIYI FPV app
- Please follow this part in the MK15 user manual
The camera is disconnected on SIYI FPV app although the status indicator on air unit is solid green. The Camera IP addresses are also correct.
Then please check the Etherent switch on MK15 by following the manual chapter 6.6.
Checked the ethernet connection as well. The Siyi FPV still shows disconnected.
Please check the video attached.
I tried updating the firmware for MK-15 controller, but the siyi assistant is not detecting it. Can you please share me a photo of the MK-15 upgrade cable. And can you share me a video of the update process for MK-15
https://drive.google.com/drive/folders/1IxJg0vdR-Tp7a3b_dkdvyrDODAPSQvse?usp=sharing
Please summarize the information and write to support@siyi.biz and we will assign you a support engineer there, thanks
Can you share any documentation on the calibaration process for ZR-30 gimbal.
@SIYI now the camera feed issue has been solved but the gimble is still not working.
can we connect over a call?
@SIYI Is possible to change between workmode of the gimbal through ardupilot? In the ardupilot documentation is an option to change between lock and follow mode, but i cant found option “FPV”.
ZR30 Firmware Update Log
- Camera Firmware: 0.1.6
- Gimbal Firmware: 0.2.2
- SIYI FPV (Windows): Original version
- SIYI FPV (Android): 2.5.15.695
- SIYI PC Assistant: 1.4.0
Detail:
- New: Support SIYI FPV (Windows) version
- New: Support DCIM standard file system and EXIF information format
- New: SIYI gimbal SDK supports obtaining attitude data from external devices for flight controller integration
- New: SIYI gimbal SDK supports obtaining GPS information and adding it to photo EXIF format
- New: AI following function (only for SIYI AI tracking module and multi-rotor drones)
- New: Adapt to Mavlink protocol control and support the integration of PX4 flight controller attitude data
Hi Frank,
Is the gimbal position issue fixed yet? Until now, I only used the gimbal in FPV mode, because otherwise the gimbal always got lost. And is it possible to use UART to command the gimabl mod? I mean switching between FPV, follow and locked.
Hi Petr,
I believe that all the issues you are concerning have been solved. Welcome to sync to the latest firmware and refer to the latest user manual.
https://siyi.biz/en/index.php?id=downloads&asd=25
You will need to pay more attention on chapter 3.8 and 6.5.
Best regards,
Frank
Hi Frank.
I use this camera and I am satisfied.
But recently there is a problem with the camera!
I can’t connect to it via LAN. The LED on the camera flashes red, red, yellow, and I don’t know what the problem is. As mentioned in the User Manual:
Camera can’t identify board, but doesn’t tell anything to what should I do!
I changed and updated the firmware, but the problem is still there.
It might be caused during firmware upgrade. The reason is that the firmware upgrade was failed.
Please do it again with an FAT32 card.
Frank, I want to change firmware to older, because the new firmware don’t work for me.
Can you send me the old version of that?
Thanks
Please write to support@siyi.biz about this
We will assist you immediately after coming back from the show