Servers by jDrones

UBlox ZED-F9P L1/L2 GNSS Unit

(Josep Olivart) #12

@jpkh we just received the pre-production prototype with the connector you suggested.
Thanks again!

(Kurt shaw) #13

Just to clarify ZED-F9P does not have L5 its E5b

(anon67614380) #14

What does this mean in terms of performances?

(Josep Olivart) #15

Hi @anon67614380 in this webinar u-blox explains why right now L1+L2+E5b is better than L1+L5.
You will need to register to view the webinar.

(Pascal_P) #16

Very interesting project @jolivart
Is there a way to get Rinex rawdata from the board ?

(Josep Olivart) #17

@Pascal_P yes, the message UBX-RXM-RAWX contains the information to generate a RINEX3 observation file:
pseudorange, Doppler, carrier phase, phase lock, …

The ZED-F9P interface description document in u-blox website contains more information.

(Pascal_P) #18

thanks @jolivart so I have to add SD card through Arduino or direct logging is possible ?

(Josep Olivart) #19

@Pascal_P, simpleRTK2B doesn’t support data logging directly.
You can use an Arduino to log the data or you can connect a data-logger (likes this one) directly to the simpleRTK2B UART.
The data-logger can be powered from the simpleRTK2B board.

(Pascal_P) #20

great solution, thanks for your very quick answer !

(Pascal_P) #21

Hi @jolivart , sorry to come back and ask again, but I tried to translate without success an UBX file I found on your pages (Untitled_181025_141503_ZED_fraga2.ubx), does it have the RXM messages ? If not have you got one UBX with full raw data inside ?
I used TEQC and RTKconv.

(Josep Olivart) #22

Hi @Pascal_P, the log files you looked don’t have the RAWX message enabled.
I have just uploaded a log file with this message enabled:
This data is fresh, collected with the simpleRTK2B antenna placed in a window of a tall building (the signal quality is bad), just to let you check the RAW messages.

(Pascal_P) #23

I backed up your project. My goal is to integrate your boards inside a Pixhawk / PPK solution. It looks very promising.

(Josep Olivart) #24

Thanks a lot :slight_smile:

(Nathan E) #25

@jolivart I read that the kickstarter was successful and units will be shipping to customers in the next few weeks. Any chance I can get mine sooner? :wink:

(Drew Sandlin) #26

@jolivart just received the Ardusimple module today. It but looks like I’ll have to get one of those DF13 to JST-GH cables before I can really play around with it. The Pixhawk I’m using has the DF13 connectors on it and don’t have any JST connectors lying around that I can use to make a franken-cable.

You guys might consider including the option to add one of these cables to your purchase for a small fee, I imagine I’m not the only person still using an old Pixhawk with the DF13 connectors on it.

While I wait for that cable I’m going to play around with ublox’s U-Center software and see how they perform!

Also, @jpkh do you know what drove the change? Just curious for my own educational benefit :slight_smile:

(Luka Jurjevic) #27

It does not have EXTINT pin exposed? If it had it would be so great. But still maybe it is not that necessary with 20hz rate, at least for the copters.

(anon67614380) #28

Really curious about rtk performances.

(Sebastian) #29

Dear all,

I am non-affiliated to electronics that’s why I am raising a potentially obvious question.

For my civil engineering purposes I am looking for a low-cost high precision GPS bluetooth receiver with post-processing correction attached in order to reach between decimeter to centimeter accuracy depending on the correction service available. I would like to use the receiver to attach to an Android tablet to pass information to a GIS system on the tablet like Qfield. I came across the video post from

From what I understand is that simplertk2b streams information as pre-configured by U-center ( to the bluetooth module. The later is visible to GNSS commander which corrects the location as configure within GNSS commander and sends that to Android as a GPS location replacement for the internal GPS of the tablet. Thus the location becomes available to an Android GIS application like Qfield.

If somebody could shortly reply on this to confirm I would highly appreciate and ease ordering for a test environment.

Best regards


(Josep Olivart) #30

Which backer/order number do you have?

(Nathan E) #31

1940 from 11/28/2018